联系电话:0755-27622763
E-mail:sales@szyn.net
当前位置: 首页 > 产物中央
智能包边机Auto Edge Taping Machine
澳门金沙js57com
智能包边机Auto Edge Taping Machine

智能包边机是深圳市永能机械有限公司自立研发,环球创始对PCB沉金板边停止主动包胶的装备,替换现在由野生包边的工艺。

   Auto Edge Taping Machine is self-developed The world's first equipment by Shen Zhen Yong Neng Machinery Co. Ltd.  Which used for PCB gold plate edge automatic encapsulation equipment to replace the current process by artificial wrapping.

澳门金沙网上在线娱乐


规格参数(characteristics):

一、工艺流程Process flow:点头/包边/出料→转向→点头/包边/出料→收板

Tapping / wrapping / discharging / steering / wrapping / discharging

二、 根基规格Basic specification:

1) 收支料偏向Incoming and outgoing direction: 左进右出Left in and out of right

2) 外形尺寸External dimensions: 6936mm(L)×1480mm(W)×1396mm(H)

3) 最大过板尺寸Max PCB size:730mm×730mm

4)  最小过板尺寸Min PCB size:300mm×300mm

5) 板薄局限PCB thickness: 0.8mm~4.0mm/0.35mm-0.8mm

6) 运用胶带宽度Tape width: 12mm~35mm

7) 线速Line speed: 0.5~10m/min(可调tunable)

8) 电源 Machine power supply: 380V,50Hz

9)  功率 interiorinput power: 约about  3.0KW

10)氛围压力要求(Air pressure requirement)5-8KG/CM²

11)运送速度(speed of transmission)0.5-6m/min

12 运送里高度Transport surface height: 1020mm (露垫脚 including cushion foot)

 三、体系规格System specification:

    点头/包边/出料Tapping/wrapping/discharging

 1)功用:再次经由过程进板轴轮将胶带对折揭于板的双方,再正在Ф45 的包胶轴的感化下将胶带紧贴于板的双方。Function: fold the tape on both sides of the board again through the inlet axle wheel, and then attach the tape to the both sides of the board under the Ф45mm  action of the roller shaft .

2)机体长度Length2233mm

3) 运送机电 interiorinput power:0.75KW

4) 机架Body frame:粉体烤漆Powder baking paint

5) 定位体式格局location mode:顶降Jacking

6) 点头体式格局Tapping mode:中央定位center finding

7)  压辘轴Roller shaft:接纳Ф45 的包胶轴运送轴,Ф40 Adops Ф45 rubber shaft and the wheel sheet is Ф 40.

  转向机 Corner machine

1)   机体长度Length:1600mm

2) 轮片wheel sheet:接纳Ф50 的轮片adops Ф50 wheel sheet

3)运送机电interiorinput power:0.4KW 

4)  机架Body frame:粉体烤漆Powder baking paint

5)功用:当板进入转角机后,经由过程扭转台将板扭转九十度,使未包边的板板边取运送偏向同等

Function: when the plate enters the corner machine, the plate is rotated 90 degrees through the rotating table, so that the unwrapped edge of the plate is consistent with the conveying direction

点头/包边/出料Tapping / wrapping / discharging

1)  机体长度Length2233mm 

2)  运送机电 interiorinput power:0.75KW 

3)   机架Body frame:粉体烤漆Powder baking paint

4) 定位体式格局location mode:顶降Jacking

5) 点头体式格局Tapping mode:中央定位center finding

6)  压辘轴Roller shaft:接纳Ф45 的包胶轴运送轴,Ф40 Adops Ф45 rubber shaft and the wheel sheet is Ф 40.

7)功用:再次经由过程进板轴轮将胶带对折揭于板的双方,再正在Ф45 的包胶轴的感化下将胶带紧贴于板的双方。Function: fold the tape on both sides of the board again through the inlet axle wheel, and then attach the tape to the both sides of the board under the action of the Ф45 roller shaft.

             托盘式支板机Tray type plate collecting machine

           1) 机体长度 Length :870mm

2) 运送轴Conveying shaft:接纳Ф40 包胶轴  adops Ф40  rubber shaft

3) 运送机电 interiorinput power:0.4KW

3) 机架Body frame:粉体烤漆Powder baking paint

4) 板宽调治Plate width adjustment:经由过程PLC 掌握步进机电调治板宽Adjusting Plate width of Stepper Motor by plc

5) 功用:主动支板,削减板面刮花。Function: automatically retracts the board, reduces the surface scraper.

四、阐明Description

1、整机接纳 PLC 及触摸屏掌握 The whole machine is controlled by plc and touch screen;

2、 计数功用:经由过程光电感到,正在触摸屏显现做板数目;Counting function: through photoelectric induction, display the number of panels on the touch screen

3、 具有胶带用完主动报警功用(胶带用完后,装备主动报警,运送住手,改换胶带后按复位键装备主动启动)Automatic alarm function for tape use (automatic alarm of equipment after tape is used, s of conveyance, automatic start of equipment by reset key after replacing tape)

4、板尾胶带预留长度为 10~15mm 之间;The reserved length of plate tail tape is between 10~15mm;

5、产能:730mm*730mm 的板,每分钟能够包片板 Capacity: 730mm*730mm board, 5 sheets per minute

6、胶带规格ape specification

① 蓝胶内径Blue gum inner diameter¢80mm,外径external diameter<140mm;

② 绿胶、白胶内径inner diameterof green or rad tape¢76.2mm,外径external diameter<140mm;

7、包边机进板轴轮为耗材,3~4 月改换一次;he feeding shaft wheel of the edge wrapping machine is a consumable material, which is replaced once in 3 ~ 4 months.

8、 此装备可取化金前处置惩罚连线,可婚配L-rack 支放板机,节约野生。This equipment can be connected with the gold pretreatment, can match the l-rack receiving and releasing machine, saving labor.